{"id":97,"date":"2026-10-31T23:57:01","date_gmt":"2026-10-31T23:57:01","guid":{"rendered":"https:\/\/siborg.ca\/blog\/2026\/10\/31\/model-transistor-leakage-currents\/"},"modified":"2026-10-31T23:57:01","modified_gmt":"2026-10-31T23:57:01","slug":"model-transistor-leakage-currents","status":"publish","type":"post","link":"https:\/\/siborg.ca\/blog\/2026\/10\/31\/model-transistor-leakage-currents\/","title":{"rendered":"How to Model Transistor Leakage Currents"},"content":{"rendered":"<p>Leakage is often treated as a specification failure measured at the end of a design cycle. That approach is too late. To <strong>model transistor leakage currents<\/strong> usefully, engineers must identify the active leakage mechanism, represent the relevant electric fields and carrier populations, and calibrate against measurements over the bias and temperature range that matters.<\/p>\n<p>For a long-channel MOS device at moderate fields, an off-state current estimate based on subthreshold transport may be sufficient. For aggressively scaled devices, reverse-biased junctions, high-field drain edges, and elevated-temperature operation, it is not. A simulation that omits the dominant mechanism can produce a smooth, converged result that is physically wrong.<\/p>\n<h2>What a transistor leakage-current model must capture<\/h2>\n<p>Leakage is not a single current. In a practical transistor, the measured off-state current can contain subthreshold diffusion, depletion-region generation, band-to-band tunneling, gate-dielectric tunneling, gate-induced drain leakage, and leakage along imperfect isolation or surfaces. The dominant contribution depends on geometry, material system, doping profile, oxide thickness, terminal bias, and temperature.<\/p>\n<p>Subthreshold leakage is controlled primarily by the channel barrier. In an nMOS device below threshold, electron diffusion from source to drain rises exponentially as the gate lowers that barrier. A useful model therefore requires credible electrostatics: gate work function, oxide or dielectric thickness, channel doping, source\/drain profiles, interface charge, and the drain-induced barrier lowering behavior of the structure.<\/p>\n<p>Reverse-biased junction leakage has a different physical origin. Shockley-Read-Hall generation in the depletion region can dominate when defect-assisted generation is significant. At high electric field, direct band-to-band tunneling or trap-assisted tunneling may become the controlling process. These mechanisms are highly sensitive to local field peaks, which means that abrupt doping profiles and insufficient mesh resolution near junction curvature can materially alter the predicted current.<\/p>\n<p>Gate leakage likewise cannot be inferred from channel leakage. Its calculation requires a tunneling formulation appropriate to the dielectric stack and field regime. A model that treats the gate insulator as an ideal boundary may still predict drain current well, while missing a leakage term that controls standby power or long-term reliability screening.<\/p>\n<h2>Start with the measured operating question<\/h2>\n<p>Before selecting equations, define what the simulation is expected to answer. The right setup for an off-state current at room temperature is not automatically the right setup for a retention failure at 125 degrees C or a high-voltage leakage limit.<\/p>\n<p>Establish the terminal biases, temperature range, current components of interest, and acceptable error. For example, an engineer studying Ioff in a logic transistor may sweep gate voltage below threshold at several drain biases. A power-device engineer may instead focus on reverse drain bias, junction temperature, and the peak electric field near an edge termination. These are related problems, but they require different physical models and different attention to geometry.<\/p>\n<p>Measured current should also be separated where possible. If total drain leakage changes strongly with gate voltage, subthreshold transport or gate-induced drain leakage may be implicated. If it rises steeply with temperature at a fixed reverse junction bias, generation through depletion-region states may be more likely. Field-driven tunneling can show a much stronger dependence on reverse bias than on temperature. Such signatures do not replace device simulation, but they prevent calibration from becoming an exercise in fitting one curve with the wrong mechanism.<\/p>\n<h2>Solve electrostatics and transport together<\/h2>\n<p>The starting point for device-level leakage analysis is the coupled solution of Poisson&#8217;s equation and electron and hole continuity equations. Poisson&#8217;s equation determines the potential and electric field from the material properties, doping, fixed charge, and mobile carriers. The continuity equations determine carrier transport through drift, diffusion, recombination, generation, and applicable tunneling terms.<\/p>\n<p>This coupling matters because leakage mechanisms change the carrier population that helps determine the field distribution. A fixed-field postprocessing estimate can be useful for screening, but it is not equivalent to a self-consistent solution when leakage is large enough to perturb charge or when field localization is central to the result.<\/p>\n<p>Use transport models consistent with the device and bias regime. Mobility degradation, carrier statistics, recombination parameters, and incomplete ionization can all influence the result. In lightly doped or high-temperature regions, assumptions that seem secondary at nominal conditions may affect the extracted leakage slope. In heavily doped junctions, band-gap narrowing and degeneracy can shift the local carrier concentrations enough to matter.<\/p>\n<p>There is no benefit in enabling every available model by default. Each added model introduces parameters that must be justified or calibrated. A compact simulation for a planar silicon MOSFET may need subthreshold transport, Shockley-Read-Hall generation, and a carefully defined temperature dependence. A high-field device may additionally need field-dependent generation and tunneling. The appropriate model set follows the failure hypothesis, not a preference for maximum complexity.<\/p>\n<h2>Mesh where the current is created<\/h2>\n<p>Leakage current often originates in a small fraction of the device. The drain-side channel barrier, depletion edge, gate overlap, junction corner, and dielectric interface are common examples. A mesh that is adequate for terminal capacitance or an on-state IV curve can underresolve these localized regions.<\/p>\n<p>Refine the mesh at steep doping gradients and expected field maxima, then test whether the leakage prediction changes materially with further refinement. The test should compare not only total current but also potential contours, peak field, generation rate, and current-density distribution. A stable terminal current with a shifting peak field can still be a warning sign when a tunneling model is used.<\/p>\n<p>Mesh refinement has a cost. It increases the nonlinear problem size and can make bias sweeps slower. The practical objective is not the finest possible grid everywhere. It is a grid that resolves the mechanisms controlling the design decision. Two-dimensional <a href=\"https:\/\/siborg.ca\/microtec.html\">process and device simulation<\/a> is often the efficient choice when the relevant cross section is well represented in a plane. A three-dimensional calculation becomes necessary when corner effects, nonuniform contact geometry, current spreading, or <a href=\"https:\/\/siborg.ca\/siblin.html\">thermal gradients<\/a> govern the leakage path.<\/p>\n<h2>Calibrate parameters without hiding missing physics<\/h2>\n<p>Calibration should proceed from independently known quantities to uncertain defect-related parameters. Start with dimensions, process-derived doping profiles, dielectric thickness, and material constants. Then compare threshold behavior, subthreshold swing, junction characteristics, and temperature trends before attempting to match a single off-current value.<\/p>\n<p>A close fit at one voltage and temperature is weak evidence. Different combinations of interface charge, lifetime, trap density, and tunneling parameters can generate similar current at one point. Bias and temperature sweeps expose whether the model has the right physical dependence. If the measured current increases with temperature while the simulated current does not, increasing a tunneling coefficient may improve one data point while making the model less credible.<\/p>\n<p>Parameter values should remain traceable. Record their source, fitted range, and the measurements used for extraction. This is particularly important for lifetime and trap-assisted mechanisms, since these quantities can vary with process history, stress, and local material quality. A calibrated parameter set is not automatically portable across wafers, layouts, or generations of a process.<\/p>\n<h2>Use simulation to separate competing mechanisms<\/h2>\n<p>The value of a leakage simulation is not limited to predicting a terminal number. It can identify where carriers are generated, which terminal collects them, and which process or layout change is most likely to reduce the current.<\/p>\n<p>Run controlled model comparisons. Solve the same bias point with and without a selected generation or tunneling mechanism, while keeping the electrostatic solution consistent. Inspect the spatial distributions of current density, recombination-generation rate, carrier concentration, and electric field. If removing a mechanism changes the total current but not the location of the hot spot, the device may have coupled leakage paths. If the hot spot moves with drain bias, the field profile rather than the bulk defect population may be setting the limit.<\/p>\n<p>For two-dimensional semiconductor process and device work, MicroTec can support the progression from diffusion profile to device simulation without requiring an oversized software suite. The useful workflow is direct: construct or import the process profile, define the device cross section and contacts, select only the physics required by the hypothesis, and validate the result against measured bias and temperature behavior.<\/p>\n<h2>Treat temperature as a model discriminator<\/h2>\n<p>Temperature sweeps are among the most informative leakage experiments because the underlying mechanisms respond differently. Thermal generation generally rises strongly with temperature. Subthreshold leakage reflects both carrier statistics and threshold-voltage shifts. Direct tunneling may show a weaker temperature dependence, although the full device response can still be affected by temperature-dependent band structure and electrostatics.<\/p>\n<p>The simulation should use consistent temperature-dependent material and transport parameters. Holding band gap, intrinsic concentration, mobility, and recombination terms fixed while changing only the boundary temperature can create an artificial trend. Conversely, a broad temperature model with poorly constrained trap parameters can imply precision that the data does not support.<\/p>\n<p>A useful engineering result is therefore a bounded prediction: the expected leakage range for stated process and operating assumptions, along with the mechanism that dominates at each condition. That result gives process, design, and reliability teams something actionable. It identifies whether the next change should be a channel-profile adjustment, junction redesign, dielectric improvement, field-plate modification, or a measurement campaign focused on defects.<\/p>\n<p>The most reliable leakage model is not the one with the most enabled equations. It is the one that explains the observed bias, temperature, and spatial behavior well enough to guide the next engineering decision.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>Model transistor leakage currents with physically consistent electrostatics, transport, and temperature assumptions to support defensible device design decisions.<\/p>\n","protected":false},"author":0,"featured_media":98,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[],"class_list":["post-97","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-uncategorized"],"_links":{"self":[{"href":"https:\/\/siborg.ca\/blog\/wp-json\/wp\/v2\/posts\/97","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/siborg.ca\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/siborg.ca\/blog\/wp-json\/wp\/v2\/types\/post"}],"replies":[{"embeddable":true,"href":"https:\/\/siborg.ca\/blog\/wp-json\/wp\/v2\/comments?post=97"}],"version-history":[{"count":0,"href":"https:\/\/siborg.ca\/blog\/wp-json\/wp\/v2\/posts\/97\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/siborg.ca\/blog\/wp-json\/wp\/v2\/media\/98"}],"wp:attachment":[{"href":"https:\/\/siborg.ca\/blog\/wp-json\/wp\/v2\/media?parent=97"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/siborg.ca\/blog\/wp-json\/wp\/v2\/categories?post=97"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/siborg.ca\/blog\/wp-json\/wp\/v2\/tags?post=97"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}